Mts Fatigue Template Manuel d'utilisateur Page 24
- Page / 122
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4.1.0 Open the Controller Station
To open the controller station:
1. Start the Station Manager application.
2. In the Open Station window, select a a configuration file.
3. Click Open to open the configuration file.
4.2.0 Prepare Controller Station for Operation
The following procedure provides a basic outline of the steps required to prepare the controller station for
specimen installation and test operation.
1. Make sure all sensors are properly calibrated.
2. Make sure the test channels are properly tuned.
3. Make sure the polarity of the sensor signals are properly set for the test.
4. Set up error detectors.
5. Set up limit detectors.
6. After the Series 793 Station Manager application is properly set up for operation, make sure the user
access level is not set to Configuration.
The test control application will not allow you to connect to a station when the Station Manager application
user access level is set to Configuration.
4.3.0 Enable Manual Control
To enable manual control of the Station Manager controller:
1. On the Station Manager Station Controls toolbar, click Manual Command.
2. Select the Enable Manual Command check box.
3. Select a control mode.
You control the actuator for specimen installation with a control knob on a control panel mounted near the
load unit. Select your preference for a control mode, a channel limited channel (CLC) control mode, a load
control mode, or a stroke control mode can be used.
4. Make sure error and limit detectors are set up.
Because of the potential danger of working near high-pressure hydraulic systems, you must set proper
limit and error detectors before installing specimens.
5. Apply hydraulics, and if necessary, reset interlocks.
24 MTS TestSuite
4.0 Test Setup
- MTS TestSuite 1
- Contents 3
- 1.0 Technical Support 9
- 2.0 Preface 13
- Hypertext links 15
- MTS TestSuite 15 15
- 3.0 Overview 17
- 3.1.0 Template Overview 18
- 3.1.2.0 Fatigue Templates 19
- 3.2.1.0 Importing Legacy Data 21
- 4.0 Test Setup 23
- 4.3.0 Enable Manual Control 24
- 4.4.0 Install Specimen 25
- 4.5.0 Disable Manual Control 26
- Strain Template 27
- 5.1.0 Set Up the Test 28
- 5.2.0 Define Test Parameters 30
- 5.3.0 Run the Test 33
- 5.3.3.0 Strain Test 34
- 5.4.0 View Test Results 35
- 5.5.0 Analyze Data 36
- 5.5.2.0 Analyze the Test Runs 38
- 6.1.0 Set Up the Test 40
- 6.2.0 Define Test Parameters 42
- 6.3.0 Run the Test 45
- 6.3.9.0 Strain Test 48
- 6.4.0 View Test Results 49
- 6.5.0 Analyze Data 49
- 6.5.2.0 Analyze the Test Runs 52
- Load Test Template 53
- 7.1.0 Set Up the Test 54
- 7.2.0 Run the Test 56
- 7.2.7.0 Measure Modulus 59
- 7.3.0 View Test Results 60
- 7.4.0 Analyze Data 61
- 7.4.2.0 Analyze the Test Runs 62
- 8.0 Transition Test Template 65
- 8.1.0 Set Up the Test 66
- 8.2.0 Run the Test 68
- 8.2.5.0 Transition Parameters 70
- 8.2.6.0 Load Test Parameters 70
- 8.2.10.0 Measure Modulus 72
- 8.2.11.0 Strain Test 72
- 8.3.0 View Test Results 73
- 8.4.0 Analyze Data 74
- 8.4.2.0 Analyze the Test Runs 76
- 9.0 Transition Test Elevated 77
- Temperature Template 77
- 9.1.0 Set Up the Test 78
- 9.2.0 Run the Test 80
- 9.2.4.0 Transition Parameters 81
- 9.2.5.0 Load Test Parameters 82
- 9.2.6.0 Load Test 82
- 9.2.12.0 Measure Modulus 84
- 9.2.16.0 Strain Test 85
- 9.2.18.0 Load Test 86
- 9.3.0 View Test Results 87
- 9.4.0 Analyze Data 87
- 9.4.2.0 Analyze the Test Runs 90
- 10.0 ASTM Trapezoidal Strain 91
- Template 91
- 10.1.0 Set Up the Test 92
- 10.2.0 Run the Test 94
- 10.2.7.0 Measure Modulus 97
- 10.2.9.0 Strain Test 98
- 10.3.0 View Test Results 99
- 10.4.0 Analyze Data 100
- 11.0 ASTM Trapezoidal Strain 103
- Elevated Temperature Template 103
- 11.1.0 Set Up the Test 104
- 11.2.0 Run the Test 106
- 11.2.8.0 Measure Modulus 109
- 11.2.15.0 Strain Test 113
- 11.4.0 Analyze Data 114
- 11.3.0 View Test Results 114
- MTS TestSuite 119 119
- 120 MTS TestSuite 120
- 100-256-292 D 121
Produits connexes et manuels pour Matériel Mts Fatigue Template
Matériel Mts TW Elite Manuel d'utilisateur
(132 pages)
(132 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.868 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels