Mts Fatigue Template Manuel d'utilisateur Page 87
- Page / 122
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9.2.21.0 Test Completion
When the test is complete, the test stops and you can run the reports. A variety of reporting options satisfy
the standard reporting requirements. When you have generated the reports, you can end the test by clicking
Done. When you have ended the test, you cannot continue to cycle the test or generate reports without the
Reporter Add-In for Excel.
9.3.0 View Test Results
After the test run completes, you can view the test results.
1. In the Explorer panel, click the name of the test run.
2. Click Results.
3. Click on the different tabs to view different types of results.
9.3.1.0 Fatigue Test Results
The Test Results show the following information about the test run:
• Variable Summary shows all the parameters and their last values for the test run.
• History shows minimum-maximum or peak-valley cycle data in relation to time or an index, such as a
data group, data point, or cycle number. The Y-axis presents data values and the X-axis presents index
values.You can select variables for the chart after the test is done.
• Hysteresis shows the cyclic or group data produced during a test cycle.You can select variables for the
chart after the test is done.
• Variable Array Chart shows all data points that are collected and calculated during each test cycle and
stored in arrays.
• Data Acquisition shows data that was acquired during the test activity. A tab is available for each Data
Acquisition activity.
9.4.0 Analyze Data
9.4.1.0 Strain View
The template is preconfigured with an analysis definition that conforms to the analysis portion of the ASTM
standard.The analysis definition can be used to analyze the test run in either the Fatigue Analyzer or Fracture
Analyzer application and contains the following tables and charts.
MTS TestSuite 87
9.0 Transition Test Elevated Temperature Template
- MTS TestSuite 1
- Contents 3
- 1.0 Technical Support 9
- 2.0 Preface 13
- Hypertext links 15
- MTS TestSuite 15 15
- 3.0 Overview 17
- 3.1.0 Template Overview 18
- 3.1.2.0 Fatigue Templates 19
- 3.2.1.0 Importing Legacy Data 21
- 4.0 Test Setup 23
- 4.3.0 Enable Manual Control 24
- 4.4.0 Install Specimen 25
- 4.5.0 Disable Manual Control 26
- Strain Template 27
- 5.1.0 Set Up the Test 28
- 5.2.0 Define Test Parameters 30
- 5.3.0 Run the Test 33
- 5.3.3.0 Strain Test 34
- 5.4.0 View Test Results 35
- 5.5.0 Analyze Data 36
- 5.5.2.0 Analyze the Test Runs 38
- 6.1.0 Set Up the Test 40
- 6.2.0 Define Test Parameters 42
- 6.3.0 Run the Test 45
- 6.3.9.0 Strain Test 48
- 6.4.0 View Test Results 49
- 6.5.0 Analyze Data 49
- 6.5.2.0 Analyze the Test Runs 52
- Load Test Template 53
- 7.1.0 Set Up the Test 54
- 7.2.0 Run the Test 56
- 7.2.7.0 Measure Modulus 59
- 7.3.0 View Test Results 60
- 7.4.0 Analyze Data 61
- 7.4.2.0 Analyze the Test Runs 62
- 8.0 Transition Test Template 65
- 8.1.0 Set Up the Test 66
- 8.2.0 Run the Test 68
- 8.2.5.0 Transition Parameters 70
- 8.2.6.0 Load Test Parameters 70
- 8.2.10.0 Measure Modulus 72
- 8.2.11.0 Strain Test 72
- 8.3.0 View Test Results 73
- 8.4.0 Analyze Data 74
- 8.4.2.0 Analyze the Test Runs 76
- 9.0 Transition Test Elevated 77
- Temperature Template 77
- 9.1.0 Set Up the Test 78
- 9.2.0 Run the Test 80
- 9.2.4.0 Transition Parameters 81
- 9.2.5.0 Load Test Parameters 82
- 9.2.6.0 Load Test 82
- 9.2.12.0 Measure Modulus 84
- 9.2.16.0 Strain Test 85
- 9.2.18.0 Load Test 86
- 9.3.0 View Test Results 87
- 9.4.0 Analyze Data 87
- 9.4.2.0 Analyze the Test Runs 90
- 10.0 ASTM Trapezoidal Strain 91
- Template 91
- 10.1.0 Set Up the Test 92
- 10.2.0 Run the Test 94
- 10.2.7.0 Measure Modulus 97
- 10.2.9.0 Strain Test 98
- 10.3.0 View Test Results 99
- 10.4.0 Analyze Data 100
- 11.0 ASTM Trapezoidal Strain 103
- Elevated Temperature Template 103
- 11.1.0 Set Up the Test 104
- 11.2.0 Run the Test 106
- 11.2.8.0 Measure Modulus 109
- 11.2.15.0 Strain Test 113
- 11.4.0 Analyze Data 114
- 11.3.0 View Test Results 114
- MTS TestSuite 119 119
- 120 MTS TestSuite 120
- 100-256-292 D 121
Produits connexes et manuels pour Matériel Mts Fatigue Template
Matériel Mts TW Elite Manuel d'utilisateur
(132 pages)
(132 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.361 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels